![trimble survey controller 12.46 user manual trimble survey controller 12.46 user manual](http://dhtechtools.com/wp-content/uploads/2015/12/s-l1600-168.jpg)
- Trimble survey controller 12.46 user manual serial number#
- Trimble survey controller 12.46 user manual windows 10#
- Trimble survey controller 12.46 user manual software#
- Trimble survey controller 12.46 user manual Bluetooth#
- Trimble survey controller 12.46 user manual series#
testing your equipment before heading to the field.
![trimble survey controller 12.46 user manual trimble survey controller 12.46 user manual](https://i.ebayimg.com/thumbs/images/g/SYYAAOSwJp5frXo8/s-l225.jpg)
We hope this helps! Again, this is only intended as a quick reference - i.e. Lower reliability value is an indication that you are not receiving all of the base station corrections which can be caused by several factors. Reliability is the percentage of RTK corrections you are receiving from the base station. If 100% reliability is not achieved, you may be too far away from your base station or may have interference on the radio frequency that is selected.
![trimble survey controller 12.46 user manual trimble survey controller 12.46 user manual](https://s3.manualzz.com/store/data/033860368_1-7b5bea8d29306272dcc0f498e96085bc.png)
The Index number displayed should match the Index number of your base station (set in Survey Styles).
Trimble survey controller 12.46 user manual Bluetooth#
If you are not able to connect your TSC3 to your receiver via Bluetooth, please see our guide for: Setting up Bluetooth connections Prior to shipping your base and rover system, our support team typically has already set up Bluetooth connections between your Trimble Base and Rover receivers. Never transmit without the proper radio antenna as it can damage the radio board. ***On-screen eBubble is only available on the R10 and R12 receivers.īefore staring your base station, always check the radio channel for any other traffic or interference. Initialization has been gained - Congratulations! You are ready to measure. This could take up to 1 minute before you achieve initialization and "Fixed" RTK status.Ĩ. * Note 4ħ. Starting survey will appear while your Rover receiver is initializing. Once Reliability reaches 100%, select Accept. After your controller establishes the Bluetooth connection to the rover receiver, it will now search for a base station that is transmitting on the same radio frequency.
Trimble survey controller 12.46 user manual serial number#
You will see the name of the receiver displayed, typically the model followed by the serial number (which can be changed under Bluetooth settings).ĥ. The TSC3 / TSC7 will drop the Bluetooth connection from the base receiver and begin to connect to the Rover. Your base station is now transmitting RTK corrections.Īfter you base station has been started and transmitting RTK corrections, you can now get the rover going.Ĥ. Congratulations! Houston - we have lift off. This is the measured height of the receiver above the occupied point, typically on a tripod with optical plummet, measured from the occupied point to "Bottom of antenna mount" - a.k.a. For equipment testing - we use the "Here" feature.Ħ. Antenna height. Point name: Select from List or Key in the coordinates of your position. If creating a new job, enter the properties of the site including Coordinate system, Datum and average Project height.ģ. Select Measure: RTK, then Start base receiver.Ĥ. Your TSC3 will connect to the Base receiver via Bluetooth. Select Jobs to start and new job or open existing one.
Trimble survey controller 12.46 user manual software#
Open Trimble Access field software and select General SurveyĢ. With your base station receiver set up (and level) over a known point:ġ. Power both your Base and Rover receivers and ensure radio antennas are installed. *Note 1: If you intend to transmit on any UHF frequency for any length of time - you should use the scan feature first to ensure that channel is clear.ĭownload or Print version (.PDF) Download here Part 1: Starting Your Base Station Receiver This is a quick start guide and should be used to test your equipment BEFORE heading out to the field. If you've purchased your system from Positioning Solutions, our sales support team has already Set Up Your Bluetooth Connections, basic Survey Styles and radio settings so your equipment arrives ready to work. Many of our land survey customers are first-time users of Trimble RTK equipment.